Posts Tagged Priming

Spare Bedroom Almost Finished

So I described my work on the wardrobe and even the light fixture, but I really should have first talked about how much work I’ve done to get the bedroom ready. In reality, the wardrobe and light were like finishing touches compared to how long I spent re-wiring, adding outlets, repairing the plaster, drywalling & mudding.

First off, this room is behind the bathroom, where there was a door-sized opening connecting this bedroom with the bathroom. Since the bathroom is (nearly) finished, the opening was closed in on that side except for the hole-in-the-wall where my medicine cabinet will eventually be installed. But because the tub/shower was previously along this wall, there was major water damage even on the bedroom side of the wall. The plaster was bubbled and crumbling all along where the tub would have been. Each time I tried to scrape it flat in preparation to mud over it, it just kept crumbling. The ceiling wasn’t in the best shape either, it was sagging in the middle and had major cracks from one wall to the next. I could have spent time scraping out each crack, reattaching the plaster to the wood slats, and then mudding and sanding.

P1030371 B.jpg

But in my mind, I kept thinking it wouldn’t last long and I’d be unhappy with the ceiling in just a short while. So I decided to drywall both the ceiling and the damaged plaster wall. No need to tear the plaster off (a ridiculous amount of work, dust, mess, and trash). I found the ceiling joists & wall studs and installed the drywall right over top, making sure my screws were long enough to reach through the plaster and secure the drywall to the framing.

First though, a friend helped me re-wire this bedroom to replace the knob & tube wiring and put the room on it’s own dedicated breaker (less electrical demand on the “whole-house breaker” of whoever previously wired my electric panel). From the crawlspace to the attic, we re-wired the ceiling light, light switch, and upgraded the room from 1 lonely outlet to 1 outlet per wall – meeting today’s standard of  every 6 linear feet. This was not really an attempt to meet today’s residential electrical requirement, but more for convenience in the future since most standard lamps and other electrical items have a 6′ cord. When it came time to add outlets, rather than today’s standard height in the wall, I am installing them horizontally in the baseboard. There are already several rooms in the house where a previous owner added outlets in the baseboard, so to maintain a consistent look I decided that’s where I would add them also. The baseboards in my house are 9″ tall, so this places the outlets about 4″ off the floor. And a brown outlet and brown cover almost disappear on the dark stained woodwork.

Back to prepping the walls & ceiling. Once the drywall was hung I began to tape and mud all the seams and corners. This was my first time mudding drywall on a ceiling. Now this sounds like it would be the same as seams on the wall, but trust me it’s not the same. There is so much more coordination required with managing drywall knives while stepping up and down the step stool, and a lot more accidentally dropping (or throwing) drywall mud – landing on my pants, shoes, and the floor. I’m glad I didn’t tear the carpet out until after all this work, it caught all my mess. Lots of thin coats of mud, lots of drying time, and finally a few hours carefully sanding.

P1040656 B

No, water resistant greenboard drywall was not required for this ro0m – I purchased more than I needed when I renovated the bathroom and couldn’t return it. At the the end of the day it’s still drywall, and once painted no one will know the difference.

One detail I included in this room was an access panel to the shut-off valves for the tub & shower on the other side of the wall. It’s a simple plastic frame with a snap off cover if I ever need to do repairs or for some reason shut off the water lines to the tub.

P1040666 B

P1040735 B.jpg

While mudding  I also tried my best to fix any cracks, holes, or divots in the plaster walls. These two walls below are not drywall, but rather plaster – and there is maybe more mud on these walls than on the new drywall.

P1040661 B

I also sanded out all of the previous owners bad patch jobs, like where they slapped on spackling compound and didn’t sand it flat to the wall. Sanding is a messy job, and I always forget that until I’m covered in dust after just an hour or so.

IMG_3940 B

In the end, I was pretty impressed with myself for how the walls turned out. Priming is the real reveal.

P1040685 BP1040689 BThere is one corner that isn’t perfect, but I can live with it. Imperfection is character, or so I keep telling myself.

I already had the woodwork for the windows scraped, sanded, stained & poly’d, and I was eager to nail it back into place once the walls were painted and dry. I still need to fill & stain the nail holes, but I am so happy with how this room is coming together. It will actually be the most complete room in the house in another weeks time when I get the baseboards nailed into place – and take some after photos of the full room!

 

, , , , , , , , , ,

Leave a comment

Restoring Wood Windows – Putty, Prime, & Paint

Part 2 of restoring my home’s original wood windows. Part 1 is here.

Setting the glass means getting handsy with some glazing putty. Now some contractors say you can lay the glass into the rabbit using caulking or an adhesive. But I feel like that is a shortcut. The professionals who have been restoring windows for a while make a bed of the same putty that’s used on the outside of the glass, which is how wood windows would have been assembled originally 100 years ago. Recommended by all the pro’s, I use Sarco Glazing Putty, type M. I found it easy to work with, kind of like play dough. Working it like play dough for a minute or so with my hands makes it so much softer.

I lay an even thickness of putty along the rabbit on the inside the sash, using more than I need. I just move a ball of putty around the rabbit, pressing it in a few inches at a time with my palm. It’s a little messy, and it results in a lot of excess, but I wan’t squeeze out so that’s ok. Then I lay the glass on top. As carefully as I can, and often while holding my breath, I slowly work my hands around the perimeter of the glass, pressing firmly to set the glass into the putty. Also as carefully as I can, I use my glazing tool to press 2 or 3 glazing points into the groove on each side of the glass. I use these newer glazing points:

I think they are easier to set into place – and also because my first experience using the more original triangle glazier points resulted in slipping and cracking an original piece of glass, at which point I nearly gave up. (Instead I found an old glass window sash at a yard sale and was able to cut this piece of glass to fit.) The squeeze out putty can be scraped off and re-used, but using more than enough is important so that the glass makes a tight seal. Then I kind of repeat the process of pushing more putty into the rabbit with my palm, working my hand around the entire sash. I first use a glazing knife to simply push the putty tight into the groove, then it’s time time tool it smooth.

Tooling the putty is an art. Especially in the many videos online of professionals who can flawlessly tool an entire window in seconds. I spend a few minutes on each side of the glass, pressing the putty firmly into place while trying to achieve a smooth texture. Corners are a pain in the ass, I have yet to “master” a corner, but I’m getting better on each window.

IMG_3179 B

Once the putty is tooled smooth – or as close as I can get it without losing my patience – I clean up the oily residue the putty leaves on the glass. This step is kind of fun, like painting only using a white powder called (what else), whiting. It’s the same whiting the professionals use, ordered online from the same company that sells the glazing putty. My understanding is that it’s pure limestone powder – it’s not cheap, but it goes a long way. With a very soft brush it really does clean the oil residue off of the glass that the putty leaves behind. It also skins the putty to encourage it to dry faster in prep for painting.

(I feel the need to insert here that yes, I have had to order many of these window restoration supplies and materials through the internet. The hardware stores around me don’t sell and can’t get many of these products. With as much time and energy I’m investing into these windows, I don’t want to substitute on inferior quality materials and take a chance of lessening how long these repairs last.)

Now onto painting – I’ve read a few different opinions, but the professionals I worked with said that using a good latex paint does not require priming the putty – the putty is manufactured to accept paint. For paint, I went by the recommendation of The Craftsman Blogger (an incredible resource for all things old house restoration!). Instead of a regular exterior latex, I went with Sherwin Williams’ Porch & Floor Enamel. It is a latex paint, but it is formulated to dry to a hard durable finish and unlike many latex paints, it doesn’t stick to other painted surfaces once cured.

I chose my paint colors for the outside of the window to stand out. Although I couldn’t tell the original color of the outside frames, while scraping paint from the sashes I could see that most original coat of paint was actually black. I love to see old houses with colorful window & frame combinations, and I really believe the “all white” or “all beige” window & trim combinations that plague so many homes is a negative result of the replacement window industry.

IMG_3163

While scraping I found the original paint color to be black.

Although not black, I did choose a dark color for the sashes and a lighter color for the frames.

In my mind, I’m picturing a finished product something like this:

IMG_3173

I had to work up an entire exterior color scheme before I could decide on paint colors, even though I’m quite  awhile away from painting the outside of my house. But planning ahead, I was able to pinpoint the right colors for the outside of the windows. I decided on SW7069 Iron Ore for the sashes:

and SW 6105 Divine White for the window frames.

It looks more blue in this photo below, but in person its a deep navy/charcoal.

IMG_3297 B

Now the secret to a long lasting window restoration? When painting the angled surface of the glazing putty, it is essential that the paint actually goes just a little bit onto the glass around the entire perimeter. Even if only 1/16 of an inch, lapping the paint onto the glass seals the putty to the glass and, from what I’ve read, makes the difference between a glazing job that lasts 5 years and one that lasts 25+ years. So many people finish their paint job with a glass scraper and scrape off the excess paint to make a perfectly clean line at the glazing putty. This ruins that seal the paint creates.

After 2 coats of paint, I wait a full week to make sure all the paint & putty is cured completely, then it’s time to put the windows back together. I bet I spent at least 3 weeks with each window tore apart. Like I said earlier, it’s all the waiting in between priming, glazing, and painting that takes the longest. Plus the fact that I get most of my work done on the weekends, so M-F of a full work week doesn’t see much progress either.

 

At this point I’m close to putting the window back together, but there are still a few more steps to ensure the window is air-tight. These include the original type of weatherstripping as well as 2 different types of modern weatherstripping.

, , , , , , , ,

Leave a comment

Turning Gray & Choosing Paint

Since last weekend, I put a 2nd coat of primer on the bathroom walls, this one was tinted gray to ready the walls for the final paint color.

P1030721 B

At this point, both the walls and ceiling are ready for paint!

P1030719 B

So it was time to select the final paint colors. I basically knew what I wanted, but I have the unique ability to choose 50 paint samples (that anyone else would say all look identical) and mull over just how different they each look!

But our local Sherwin-Williams store was having a sale this weekend only – 40% Sale on all paints meant I had to make a decision! Although I considered almost a dozen wall colors, I decided to go bold or go home – Black Magic is the color name. For the ceiling, I chose a very pale gray named First Star, because I want the ceiling to be a bit in contrast to the white crown molding around the room. Both the ceiling and wall paint are Duration in Satin finish, which I’ve used in the past and really enjoy painting with. It’s like painting with whipped cream – it rolls and brushes on smooth and covers really well. And rather than white right out of the can for the trim, I went with a soft-white titled Snowbound, which I think will look a little less stark. For this, the store manager recommended ProClassic for trim & woodwork. It’s their best interior enamel, and supposed to dry to a super smooth but very hard finish. I like woodwork to be just 1 step shinier than the walls, so I purchased a full gallon in Semi-Gloss knowing I might use it in other rooms as well.

I put the sample board together to show what all of the room finishes will look like together:

bathroom paint samples

The wood represents the dresser I will transform into a vanity, as well as the bathroom door. I went through my stash of salvaged doors – (what, doesn’t everyone have a stash of salvaged woodwork, doors, light fixtures, and other random antique home parts and pieces?) – and I have a 5 panel door that should work great. It will need cut down about 2 inches in height, but the width is almost perfect. I’ll probably have to re-align the hinges, and perhaps the striker plate too. A few dings and chips, but it will look great with a little patching, sanding, and some stain to even out the imperfections. Almost all of the hardware in the bathroom will be brushed nickel – silver with almost a pink/gold hue. And how about that light bulb? I had a very successful shopping trip to two different architectural salvage stores in Fort Wayne. I mixed and matched some vintage light fixtures and cylindrical globes to assemble what will be an awesome pair of wall sconces once refurbished. Not exactly what I was picturing, but $15/sconce feels so much better than $100/sconce – and they will give much the same effect. But for now they are safely stored away until the walls are ready. Now begins the week of bathroom tile!

, , , , ,

Leave a comment