Posts Tagged Refinishing
Spare bedroom, that is.
Several months without a post. That doesn’t mean I haven’t been busy, just that I haven’t been working on my own home. In fact, in the last two months I’ve helped my brother-in-law with different aspects of their master bathroom remodel, and a partial remodel on my mother’s kitchen (reconfigured the existing base cabinets, installed a dishwasher, built additional base cabinets, and installed new countertop).
But sometime in between building cabinets in my unheated garage in the middle of an Ohio February, I finished painting the spare bedroom and nailed the window trim & baseboards back into place. Wow, did that make a difference!
While reinstalling the baseboard, I added outlets to the perimeter of the bedroom through the baseboard. Each bedroom only had 1 original outlet to begin with. And I added the new outlets in the baseboard, just as the existing outlets were placed. I used brown outlet and outlet covers to help them disappear into the dark woodwork.
I already described the process of sanding & re-painting the wardrobe, and installing the light. Along with all new wiring, I can add this room to the 99% finished list along with the bathroom and laundry. (Like nearly every other room, the floor needs a few nails here and there to secure the boards, and then a whole-house floor refinishing party.)
Lastly, I found a door to fit at an architectural salvage store (the spare bedroom was door-less when I bought the house). It matches the bathroom door, but unfortunately was painted on one side. I spent the better part of 2 days stripping the paint – first white, then orange underneath.
It was the correct height, but actually just about 1/4″ too narrow. I glued & clamped a thin piece of pine to the hinge edge of the door, then with a hand plane and sandpaper made it flush with the sides of the door.
The other side was stained & varnished almost a matching color to my woodwork, so I just sanded off the finish and then re-stained both sides of the door to blend the color. It took 2 coats of stain on the freshly stripped side to get dark enough, then 2 coats of satin polyurethane. The piece I added to meet the right width is almost unnoticeable.
I’ve been collecting glass doorknobs when I find them inexpensively at antique stores or Goodwill, so I just had to buy the mortise latch threaded spindle – which I was pleasantly surprised to find they still sell at the hardware store. For me, there is nothing so rewarding as the feeling of putting the finishing touches on a completed project.
So now I begin the same process to the other bedroom, starting with stripping the woodwork and restoring the windows again.
Although I went ahead and stained & poly’d most of the laundry room trim and baseboard, there were some small pieces of baseboard left that were
lost – hiding – waiting in the garage. And the built-in broom closet had a busted panel in the door, so I removed it from the hinges and it was waiting in the garage also. Just like the woodwork had 50 layers of paint, so does all the hardware. The hinges are salvagable (although I destroyed the screws trying to scrape the paint off of them to back them out). The door latch was busted, but there are other examples in the house so I know what type to look for.
I was able to get the busted upper panel out pretty easily – the frame around it on the back of the door was split around the panel, probably when it was broken originally. I carefully scraped the paint off each of the 2 pieces first, I guess I was concerned that once the panel was glued back together there would be paint in the seam that I wouldn’t be able to get out. Once scraped, I glued & clamped the broken panel, and went to scraping the door.
The hardware was caked with paint. This picture is actually after the first soaking and scrub with a brass bristle brush. The secret for removing paint off of metal – hinges, knobs, handles – is a good soaking for several hours in very hot water with a touch of baking soda. An old crock pot works really well for this, set it and forget it.
The paint on these was so thick, no wonder the door would barely open or close. It took two soakings and a little bit of scrubbing.
But they came out perfectly clean. Some new screws and these will be ready for another hundred years of action.
I’ve got the first coat of stain on the door, the panel, and the miscellaneous baseboard pieces. But to achieve the rich mahogany color that was originally under the paint, I have to wait a full day between the 1st and 2nd layers of stain – the stain has to build. If I try to apply the 2nd layer too soon, it simply melts the first layer and I don’t get the rich, full color. I’ll piece the panel back into it’s frame before I brush on the polyurethane, keeping it in place with some thin pieces tacked around it on the back. I think something like screen door trim will do the trick.
One more layer of stain, and 2 coats of poly – and the door will be back where it belongs. And the laundry will be almost, almost, almost finished.
This post is written post-completion, kind of playing catch-up with the blog so it matches my progress on the house. For once the house work is actually ahead of journaling.
The laundry room, though the smallest room in the house, probably had the worst plaster of any room in the house. Lots of large cracks, peeling paint on every wall and the ceiling, and of course the woodwork had layer after layer of paint on it.
I immediately took down the cabinet on the right, and not too long after that I ripped up the linoleum and 1/2″ plywood it was glued to. There wasn’t too much glue holding the plywood down, and underneath there was the original fir floors, although filthy and lots of stain. There is evidence of quite a lot of water leaking, from the flooring to the baseboards, but luckily they aren’t rotten, just stained.
I’ve tried heat gun and every chemical in the hardware store, but a sharp scraper seems to be the best tool for removing paint from the woodwork. Note the fan blowing dust outside, and the plastic taped around the doorway to the kitchen to keep any paint dust out of the living areas of the rest of the house.As the paint came off the woodwork, I also scraped all loose paint off of the walls – which was a lot. The only thing missing is a photo of the paint chips on the floor, about an inch thick.And all the cracks. The plaster itself isn’t loose or crumbling, just lots of deep cracks. I think the roof must have been leaking down this wall where the windows are.Then it was time to throw more mud – drywall mud. I’m not the cleanest with it, I can get it semi-smooth on the walls, but I seem to drip quite a lot on the floors. I didn’t even bother to clean it up right away.
Although they didn’t all need it, I went ahead and applied drywall tape and joint compound to all of the corners throughout the room – walls and ceiling.I’m not perfect at mudding walls, but this was good practice with all the corners. Where it wasn’t perfect, a little bit of sanding when dry works really good. I found that very fine sandpaper on a square oscillating sander works good, but I have to keep it moving quick so not to sand off too much.The ceiling was terrible. It looked like it had a skim-coat at some point in the past, and it took so many layers of mudding, sanding, mudding, and sanding. In the end, I wasn’t going for perfect. Just semi-smooth. I’ve already decided that in an old house, nothing should be “perfect,” or it won’t be an old house anymore. Character, I call it.After a long night of sanding… selfies in the reflection of the laundry room window:After a layer of primer and 2 coats of paint, voila! Not a bad ceiling after all!
I stained the woodwork first before painting the walls. It is impossible, in my opinion, to stain woodwork and not get it on the walls. Two generous coats of stain, and then I use a trim brush to prime over the sloppy stain so that it doesn’t seep through the finish paint.
Then it was time to paint. I wasn’t very picky choosing a paint color for the laundry room. It’s a small room, and there really isn’t very much style going on in there. My washer & dryer are white, the woodwork is mahogany, and I eventually plan to hang painted cabinets above the machines. But since the room opens into the kitchen, I want the two rooms to eventually feel seamless. So I picked a nice putty beige that will look good with the woodwork & the colors I already have picked for the future kitchen cabinets. The color is Loggia by Sherwin Williams (SW 7506). It’s a good neutral – not too yellow, not too pink – and the name, Loggia, brings back fond memories of my semester in Italy.
(This is where I explain, yes, the cabinet in the wall which is supposed to be a broom closet is functioning now as a handsaw cabinet. Some people have gun cabinets. I for some reason have a saw cabinet.)
I had removed the baseboards earlier before tackling the plaster repair, so I stained & poly’d them while off the walls – much easier this way. So all I had to do was nail them in place – and they fit really tightly to the walls. I didn’t feel like fixing the former outlet opening in the board above, because I knew it would be hidden by the washer. But I did purchase a brown outlet cover and screwed it overtop. A quick fix for an area that will only ever be seen during the short time it takes to switch out a washer or dryer if
when appliances are ever upgraded.
The woodwork isn’t perfect, it still has some dings and scratches. But I didn’t feel the need to sand everything out. Once again, character.Then some finishing details. Like snapping on the trim piece for the washer connection box:
For a light in the laundry room, I planned on just one fixture in the center of the ceiling. I really liked the shape and style of this Jar Pendant from West Elm, but I think I had less than their asking price in my total materials for the entire laundry room rehab. And I really didn’t want a pendant type fixture.
Over the winter I hit a couple salvage stores in Fort Wayne and found enough pieces to make something similar in a ceiling mount light. I found the metal base at one salvage store, and the glass globe at another.
A little spray paint for the base, new screws to hold the globe, and tada! Similar, but less than $15 total.
What’s next? Well, I’m gonna enlist my mother’s sewing skills to create some window coverings. I don’t really need privacy in this room, but introducing some fabric will soften the edges around the woodwork and introduce texture into an otherwise all-wall room. Cotton drop cloth, leather straps, and metal grommets – something like this:
But I’m most excited to start dealing with my beautiful but inefficient original windows – glazing putty, bronze weatherstrip, and new sash rope – here we go!